Category: At least Windows Server 2008 R2 or Windows 7
Set Teredo Server Name
This policy setting allows you to specify the name of the Teredo server. This server name will be used on the Teredo client computer where this policy setting is applied. If you enable this policy setting you can specify a Teredo server name that applies to a Teredo client. If you disable or do not configure this policy setting the local settings on the computer are used to determine the Teredo server name.
Set Teredo Refresh Rate
This policy setting allows you to configure the Teredo refresh rate. Note: On a periodic basis (by default every 30 seconds) Teredo clients send a single Router Solicitation packet to the Teredo server. The Teredo server sends a Router Advertisement Packet in response. This periodic packet refreshes the IP address and UDP port mapping in the translation table of the Teredo client’s NAT device. If you enable this policy setting you can specify the refresh rate. If you choose a refresh rate longer than the port mapping in the Teredo client’s NAT device Teredo might stop working or connectivity might be intermittent. If you disable or do not configure this policy setting the refresh rate is configured using the local settings on the computer. The default refresh rate is 30 seconds.
Set ISATAP State
This policy setting allows you to configure Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) an address-to-router and host-to-host host-to-router and router-to-host automatic tunneling technology that is used to provide unicast IPv6 connectivity between IPv6 hosts across an IPv4 intranet. If you disable or do not configure this policy setting the local host setting is used. If you enable this policy setting you can configure ISATAP with one of the following settings:Policy Default State: If the ISATAP router name is resolved successfully the host will have ISATAP configured with a link-local address and an address for each prefix received from the ISATAP router through stateless address auto-configuration. If the ISATAP router name is not resolved successfully ISATAP connectivity is not available on the host using the corresponding IPv4 address. Policy Enabled State: If the ISATAP name is resolved successfully the host will have ISATAP configured with a link-local address and an address for each prefix received from the ISATAP router through stateless address auto-configuration. If the ISATAP name is not resolved successfully the host will have an ISATAP interface configured with a link-local address. Policy Disabled State: No ISATAP interfaces are present on the host.
Set ISATAP Router Name
This policy setting allows you to specify a router name or Internet Protocol version 4 (IPv4) address for an ISATAP router. If you enable this policy setting you can specify a router name or IPv4 address for an ISATAP router. If you enter an IPv4 address of the ISATAP router in the text box DNS services are not required. If you disable or do not configure this policy setting the local host setting is used.
Set 6to4 State
This policy setting allows you to configure 6to4 an address assignment and router-to-router automatic tunneling technology that is used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet. 6to4 uses the global address prefix: 2002:WWXX:YYZZ::/48 in which the letters are a hexadecimal representation of the global IPv4 address (w. x. y. z) assigned to a site. If you disable or do not configure this policy setting the local host setting is used. If you enable this policy setting you can configure 6to4 with one of the following settings:Policy Default State: 6to4 is enabled if the host has only link-local IPv6 connectivity and a public IPv4 address. If no global IPv6 address is present and no global IPv4 address is present the host will not have a 6to4 interface. If no global IPv6 address is present and a global IPv4 address is present the host will have a 6to4 interface. Policy Enabled State: If a global IPv4 address is present the host will have a 6to4 interface. If no global IPv4 address is present the host will not have a 6to4 interface. Policy Disabled State: 6to4 is turned off and connectivity with 6to4 will not be available.
Set 6to4 Relay Name
This policy setting allows you to specify a 6to4 relay name for a 6to4 host. A 6to4 relay is used as a default gateway for IPv6 network traffic sent by the 6to4 host. The 6to4 relay name setting has no effect if 6to4 connectivity is not available on the host. If you enable this policy setting you can specify a relay name for a 6to4 host. If you disable or do not configure this policy setting the local host setting is used and you cannot specify a relay name for a 6to4 host.
Set 6to4 Relay Name Resolution Interval
This policy setting allows you to specify the interval at which the relay name is resolved. The 6to4 relay name resolution interval setting has no effect if 6to4 connectivity is not available on the host. If you enable this policy setting you can specify the value for the duration at which the relay name is resolved periodically. If you disable or do not configure this policy setting the local host setting is used.
Do not allow pinning programs to the Taskbar
This policy setting allows you to control pinning programs to the Taskbar. If you enable this policy setting users cannot change the programs currently pinned to the Taskbar. If any programs are already pinned to the Taskbar these programs continue to show in the Taskbar. However users cannot unpin these programs already pinned to the Taskbar and they cannot pin new programs to the Taskbar. If you disable or do not configure this policy setting users can change the programs currently pinned to the Taskbar.
Do not allow pinning items in Jump Lists
This policy setting allows you to control pinning items in Jump Lists. If you enable this policy setting users cannot pin files folders websites or other items to their Jump Lists in the Start Menu and Taskbar. Users also cannot unpin existing items pinned to their Jump Lists. Existing items already pinned to their Jump Lists will continue to show. If you disable or do not configure this policy setting users can pin files folders websites and other items to a program’s Jump List so that the items is always present in this menu.
Remove pinned programs from the Taskbar
This policy setting allows you to remove pinned programs from the taskbar. If you enable this policy setting pinned programs are prevented from being shown on the Taskbar. Users cannot pin programs to the Taskbar. If you disable or do not configure this policy setting users can pin programs so that the program shortcuts stay on the Taskbar.